Mazda Car Trim Clips, Fixings & Fasteners

This is probably the most common Mazda clip we sell. These are fitted to almost all modern Mazda cars produced since 2010. The clips fit into an 8m...

These small, black 6mm clips have a wide collar and are common on interior trims and panels. They are often used on boot linings, upholstery, roof ...

A common clip used by Mazda for attaching side skirts, sill mouldings and other plastic trims around the vehicle. These are very common on side ski...

This 8mm clip is very quick and easy to install and remove. They are often used for panels where access may be required such as wheel arch linings,...

These chunky and strong clips and used on the sills of several different Mazda models. The clips are used to fasten the side skirts or plastic sill...

These interior door card clips are used on a wide range of Mazda cars to hold the interior door cards in place. Our clips include the foam sealing ...

These bolts are used on several Mazda models to secure bumpers, radiator panels and wheel arch linings. Each one includes a washer.

This clip is very widely used across the Mazda range. It is used on everything from interior trim panels to bumpers, engine bay shields and wheel a...

Common on several Mazda models, these clips are normally used on bumpers undertrays, sill mouldings or other large panels and shields.

These green plastic moulding clips come with foam sealing washers. They are an identical and high quality alternative to the genuine Mazda part num...

This interior trim panel clip is widely used by Mazda. The clips are normally used on door cards but will also be found on boot linings, pillar tri...

Normally found on Mazda front or rear bumpers, these plastic fasteners expand when the centre pin is pushed in. They fit into a 5mm hole. The clips...

Normally used to secure wheel arch linings, splashguards, undertrays or bumpers, these simple screw fit plastic rivets are used on several differen...

Sometimes known as chimney nuts or spire clips, these grey plastic clips are used to join trims and panels. These are used on many different Mazda ...

This is a set of plastic fasteners used for attaching a single side skirt to the Mazda 3 (BL 2008-2013). One kit is exactly as shown in the photo a...

These yellow weatherstrip clips are fitted to most Mazda cars since 2000. The small clips fit inside the rubber seals that run around the doors, bo...

These fir tree clips are used to secure the under bonnet sound proofing insulation on most Mazda cars since around 2003. The clips fit in a 5.5mm h...

Very common across the Mazda range, this clip is used to fasten and secure a wide variety of parts. Uses include Mazda MX-5 sideskirt clips, CX-3 b...

These grey clips are used by Mazda to secure exterior trim mouldings to the sides of vehicles such as the Mazda CX-5. Each part includes a foam sea...

These distinctive white trim clips are used on the first generation of the Mazda CX-5 to secure the plastic trim that runs around the edge of the w...

This part is normally used on interior panels that sit flush against the dashboard or centre console. These trims are sometimes decorative or are u...

This clip is used by Mazda to secure the rubber seal that runs along the front or rear side of the bonnet. It's used on most modern Mazda cars incl...

These clips are a high quality replacement identical to the OE parts. Mazda use these plastic push fit rivets for a variety of uses. They can be fo...

Expanding screw fit rivets such as these will normally be used wheel arch linings, bumpers, under trays and sill mouldings.

These grey fasteners have a large rectangular collar. They fit into a 10mm hole and expand when the centre pin is inserted. They are used to attach...

These rectangular collared retaining clips are normally used for the foam bumper impact absorption panels fitted behind the bumper covers.

These grey screw edge grommets or spire clips are used to join parts without necessitating damage to the metal bodywork. This part slides over the ...

These small plastic clips are used on weatherstrip seals and rubber aperture seals. The clip head fits inside the rubber seal and then the stem of ...

These clips are used around the edges of the wheel arch. They mount onto the lip of the wing and then the plastic wheel arch liner is attached when...

Small, black trim clips that fit into 6mm hole. These parts have a wider collar than average. They are simple to fit or remove and are fitted to se...

Each of these fasteners includes a foam sealing washer. Example uses include Mazda CX-3 and CX-5 wheel arch flare and side moulding clips. The clip...

These expanding rivets are normally used to attach loose fitting panels such as wheel arch linings or splash guards. They fit into an 8mm hole and ...

These very small plastic button clips fit into a 4 to 5mm hole. They are used to secure rubber door seals or weatherstrips.

Grey plastic fasteners used by Mazda to attach the plastic trim that runs around the edge of the wheel arch. This clip is used on the Mazda CX-3 Mk...

These long grey expanding push fit clips are unusual in that they only expand at the very tip. They are used by Mazda on front bumpers and some doo...

These distinctive green trim clips are used on the exterior pillars on many modern Mazda vehicles. The clips hold the lightweight plastic trim in p...

Grey plastic trim clips with a foam sealing washer. The plastic fasteners are used on several Mazda models. They are in different places depending ...

These are a standard screw grommet used to attach parts or trims onto metal bodywork without having to screw directly into the metal.

This is a common bonnet stay holder clip on Mazda vehicles. The bonnet support rod clips into this retainer when not in use. The clips can easily b...

These green plastic clips look different before they are fitted as they have a washer that forms part of the mould. During installation, the washer...

This distinctive screw fit fastener has an oval collar. The clip is normally used for windscreen cowls or scuttle panel trims. It is used on modes ...

These plastic trim clips are used by Mazda, normally on exterior parts such as bumpers, grilles or radiator shields and guide.

This kit contains all the fasteners needed to attach the engine undertray panel on the vehicles listed below. We have researched and created these ...